The difference between mic level and line level

David Mellor

David Mellor is CEO and Course Director of Audio Masterclass. David has designed courses in audio education and training since 1986 and is the publisher and principal writer of

Friday May 15, 2020

Mic level, line level, and instrument level refer to the voltage level of mic, line and instrument signals, and also to their impedance, or current-delivering capability. Why do these differences exist?

Mic level line level

"For historical reasons" is the answer to a great many questions, inside and outside of audio. Things happened in the past that led to things being the way they are today. Like the British habit of driving on the left side of the road, which apparently stems from horse riders wanting to have their sword hand free to tackle potentially aggressive approachers. Well that's one theory.

So for various historical reasons microphones have a low output level of somewhere around 10 millivolts or so, varying of course with the loudness of the sound source and the distance of the mic from the source. They also have a lowish output impedance, typically around 200 ohms, which means they can supply quite a strong electrical current.

Line level, again going back to history, derives from 1 milliwatt of power traveling through a telephone cable with a characteristic impedance of 600 ohms. Using Ohm's law we can derive a voltage of 0.775 volts. So the level of a line output is around 0.775 volts, or you can say around a volt because we don't need to be that precise. Line level outputs are always powered so the impedance can be low, and by low we would consider anything less than about 150 ohms, and it could be a lot less. Low impedance again leads to high current delivery capability.

What about instruments? Well we can think of the electric guitar with normal passive pickups. We can see from this interesting table that an electric guitar can pump out around 150 millivolts from the strum of an E chord. That's not a bad voltage but you have to consider that it is only the energy supplied by the player that is converted to electricity. There is no other energy input. So to achieve that fairly high voltage of 150 mV, the consequence is that the output impedance is high, around 5000 to 10,000 ohms, rising further towards higher frequencies. This means that the capability to supply current is not good and significantly worse at higher frequencies.

So we can summarize mic level, line level, and instrument level thus...

I could delve further into the electronic math, but it's more interesting to explore the consequences of mis-connecting...

I could go through the other possibilities but I think you should get the gist by now. Microphones, line level sources, and instruments should each be connected to the proper input.

Oh, I didn't mention that many microphones need phantom power. You won't get that from a line or instrument input so the mic won't work at all.

And... If you connect anything but a microphone to a mic input that has 48 volts phantom power... Well you may get away with it but don't blame me if your 1959 vintage Les Paul Standard gets its pickups blown.

Like, follow, and comment on this article at Facebook, Twitter, Reddit, Instagram or the social network of your choice.

Come on the Audio Masterclass Pro Home Studio MiniCourse - 60 great hints and tips to get your home recording studio MOVING

It's FREE!

Get It Now >>

An interesting microphone setup for violinist Nigel Kennedy

Are you compressing too much? Here's how to tell...

If setting the gain correctly is so important, why don't mic preamplifiers have meters?

The Internet goes analogue!

How to choose an audio interface

Audio left-right test. Does it matter?

Electric guitar - compress before the amp, or after?

What is comb filtering? What does it sound like?

NEW: Audio crossfades come to Final Cut Pro X 10.4.9!

What is the difference between EQ and filters? *With Audio*

What difference will a preamp make to your recording?

Watch our video on linear phase filters and frequency response with the FabFilter Pro Q 2

Read our post on linear phase filters and frequency response with the Fabfilter Pro Q 2

Harmonic distortion with the Soundtoys Decapitator

What's the best height for studio monitors? Answer - Not too low!

What is the Red Book standard? Do I need to use it? Why?

Will floating point change the way we record?

Mixing: What is the 'Pedalboard Exception'?

The difference between mic level and line level

The problem with parallel compression that you didn't know you had. What it sounds like and how to fix it.

Compressing a snare drum to even out the level

What does parallel compression on vocals sound like?

How to automate tracks that have parallel compression

Why mono is better than stereo for recording vocals and dialogue