Your compressor adds noise to your recording. Why does it do that?

David Mellor

David Mellor is CEO and Course Director of Audio Masterclass. David has designed courses in audio education and training since 1986 and is the publisher and principal writer of

Wednesday August 21, 2019

Your compressor adds noise to your recording. Why does it do that?

What recordings would sound like if compressors had never been invented, I do not know. (Who said, "A whole lot better!"?)

The fact is that the sound of recording is largely the sound of the compressor. Few recordings are made without compression of at least some individual tracks, and possibly the entire mix.

But whenever you compress, you add noise. It always happens - no exceptions. So here we have a problem that requires a solution if our recordings are not to suffer.

But why does a compressor add noise? Let's look in more detail...

The action of a compressor is to reduce high levels in a signal so that they are closer to the lower levels. We say that the compressor 'reduces the dynamic range'.

The problem now is that the signal now sounds quieter because the peak levels are lower. So we need to amplify the signal back up. This is called 'make up' gain.

So now we have a signal that is as loud as it was before in the peaks, and the lower-level sections are louder too.

The problem is that the compressor has no way of distinguishing between the low level signal that you want, and low level noise that you don't want. Every signal contains some noise. There is no such thing as a noise-free recording.

So in bringing up the lower levels through make-up gain, the noise level is brought up too. What can be done?

In an individual track of just one instrument or vocal, while the instrument is playing the noise will be obscured, or 'masked' as we call it. The noise will only be audible in the gaps when the instrument stops playing.

If we can silence those gaps, then the noise will be inaudible. To do that, we need another piece of equipment - the noise gate.

A noise gate works by detecting the difference in level between the wanted signal and the noise. Where there is wanted signal, which will be higher in level than the noise, the gate lets it through. When there is just noise, the gate shuts it off.

Noise gates can be tricky to set up, but the same effect can be achieved by simply muting sections of a track when the instrument isn't playing.

It is important to realize that the above only works where there are gaps. If you compress the entire stereo mix, then there will be no gaps, hence the noise gate cannot provide any benefit.

If you compress the stereo mix, you will have to accept that it will be noisier. You can tell how much noisier - look at the gain reduction meter on your compressor (or compression plug-in) - the maximum gain reduction that it shows is equal in decibels to the amount of noise you have added.

Being able to manage noise effectively is the mark of a professional sound engineer.

Like, follow, and comment on this article at Facebook, Twitter, Reddit, Instagram or the social network of your choice.

Come on the Audio Masterclass Pro Home Studio MiniCourse - 60 great hints and tips to get your home recording studio MOVING

It's FREE!

Get It Now >>

An interesting microphone setup for violinist Nigel Kennedy

Are you compressing too much? Here's how to tell...

If setting the gain correctly is so important, why don't mic preamplifiers have meters?

The Internet goes analogue!

How to choose an audio interface

Audio left-right test. Does it matter?

Electric guitar - compress before the amp, or after?

What is comb filtering? What does it sound like?

NEW: Audio crossfades come to Final Cut Pro X 10.4.9!

What is the difference between EQ and filters? *With Audio*

What difference will a preamp make to your recording?

Watch our video on linear phase filters and frequency response with the FabFilter Pro Q 2

Read our post on linear phase filters and frequency response with the Fabfilter Pro Q 2

Harmonic distortion with the Soundtoys Decapitator

What's the best height for studio monitors? Answer - Not too low!

What is the Red Book standard? Do I need to use it? Why?

Will floating point change the way we record?

Mixing: What is the 'Pedalboard Exception'?

The difference between mic level and line level

The problem with parallel compression that you didn't know you had. What it sounds like and how to fix it.

Compressing a snare drum to even out the level

What does parallel compression on vocals sound like?

How to automate tracks that have parallel compression

Why mono is better than stereo for recording vocals and dialogue